Panasonic WJSX350 Instruções de Operação descarregar pdf (Página 33)

-31-

0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3

T – S E Q N O. 0 1 ( S T E P = 2 5 – 3 2 )

< < S T E P = 2 5 2 6 2 7 2 8 > >

C A M 2 5 2 6 2 7 2 8

P R E ( A U X ) 0 1 – – 0 2 – –

D W E L L 0 3 0 2 0 1 0 5

< < S T E P = 2 9 3 0 3 1 3 2 > >

C A M 2 9 3 0 3 1 3 2

P R E ( A U X ) – – 0 2 0 5 – –

D W E L L 0 3 0 2 0 1 0 5

3. Move the cursor to position 1 by moving the

Joystick Controller.

Enter the desired Camera Number (1-32) for each

step by pressing the Numeric buttons or the

+1CAM INC or –1CAM DEC button.

4. Move the cursor to position 2 by moving the

Joystick Controller.

Enter the associated Pan/Tilt Preset Position

Number (if applicable) by pressing the Numeric

buttons or the +1CAM INC or –1CAM DEC button.

Or select the Auxiliary Switch Mode shown below

by pressing the +1CAM INC or –1CAM DEC button.

Parameter Mode

1N: AUX1 On

1F: AUX1 Off

2N: AUX2 On

2F: AUX2 Off

5. Move the cursor to position 3 by moving the

Joystick Controller.

Enter the desired Dwell Time (1-30) by pressing the

Numeric buttons or the +1CAM INC or –1CAM DEC

button.

6. Press the HISTORY FWD button to select the next

page or press the HISTORY BACK button to select

the previous page.

Repeat the above procedures until a Tour

Sequence is completely assembled.

7. When satisfied with all of the above steps, press the

MON (ESC) button to escape from the program-

ming mode and return to the previous T-SEQ

MENU.

8. Repeat the above procedures to programme the

other Tour Sequences.

9. Move the cursor to the AUTO SKIP parameter by

moving the Joystick Controller.

Set ON or OFF by pressing the +1CAM INC or

–1CAM DEC button.

The selected parameter is effective for all

sequences (1 - 32) previously set up.

To initialize the edited sequence

Note: Once a sequence has been initialized, the previ-

ous sequence data cannot be restored.

T – S E Q M E N U

S E Q N O. = 0 1

A U T O S K I P = O F F

P R O G. C L E A R = N O

1. Move the cursor to the SEQ NO. parameter by mov-

ing the Joystick Controller.

Enter a sequence number to be initialized by press-

ing the Numeric button or the +1CAM INC or

–1CAM DEC button.

2. Move the cursor to the PROG. CLEAR parameter by

moving the Joystick Controller, then press the CAM

(SET) button.

3. Select YES by pressing the +1CAM INC or –1CAM

DEC button, then press the CAM (SET) button.

The new data set for the selected sequence num-

ber is initialized.

2. G-SEQ MENU (Group Sequence)

This table is used to programme or edit a Group

Sequence.

In each step, a maximum of eight (8) cameras can be

assigned to eight (8) monitors, each with preset position

(if applicable) or auxiliary control.

There are four (4) Group Sequences available in this

system.

Select the GROUP SEQUENCE from the PROGRAM

MENU, then press the CAM (SET) button. The G-SEQ

MENU appears on the monitor.

0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3

G – S E Q M E N U

S E Q N O. = 1

A U T O S K I P = O F F

P R O G. C L E A R = S E T

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 67 68

Comentários a estes Manuais

Sem comentários

Panasonic WJSX350 Instruções de Operação Página 33

Comentários a estes Manuais

Manuais e produtos relacionados com Câmaras de segurança Panasonic WJSX350