Panasonic VBD Instruções de Operação

PanasonicDECTDigital Cordless Telephone SystemOperatingInstructionsBefore operating this system, please readthese instructions completely.THIS EQUIPME

9Press the [volume(▲)] key or [volume(▼)] key while the PS is standing by or whileit is ringing.Pressing the [volume(▲)] key increases the volume, and

10Getting Started1. Press the [Programming] key.The PS enters the Programming mode.2. Press the [2] dial key.3. Set the tone pattern.To set the tone p

111 : Incoming call indicatorBlinks when an incoming callarrives.2 : [Speed dial] keyPress to store speed dial or make aspeed dial call.3 : [Programmi

12Names And Functions1232. Display2.1 1st line1 : Off-Hook iconThis icon is displayed when you press the [Off-hook] and [Intercom] keys to call anexte

131. Making an Exchange Line Call1.1 Making a call after hearing the outside dial toneThe telephone No. is sent after an exchange line has been secure

144. Press the [On-hook] key to terminate the call.2. Making an Internal Call2.1 Making a call after hearing the Intercom dial tone1. Press the [INT]

15Basic OperationHOLDHOLD3. Receiving CallsWhen the PS rings, press [Off-hook] key to answer.1. When the PS rings, press the [Off-hook] key.The Incomi

16APPLIED OPERATION1. Speed DialYou can store frequently-dialled outside or internal Nos. under speed dialling Nos. for quickcalling.1.1 Storing/Check

17Applied Operation4. Press the [Programming] key.This exits memory mode.• To store another telephone No. before pressing [programming] key, repeat st

18Applied Operation5. Press the [Programming] key.This exits memory mode.• To change or delete another telephone No. before pressing the [Programming]

1CONTENTSCHAPTER 1. Introduction...31. Overview ...

19Applied Operation4. Wait for the called party to answer the PS, then start your conversation.5. Press the [On-hook] key to terminate the call.2. Red

20Applied Operation2. You can also press the [Volume] keys (▲ and ▼) to select the telephone No. toredial.Pressing the [Volume] keys successively disp

21Applied Operation4. Changing from Pulse to Tone [Programming required]To change from dial pulse to tone signals during a call or while you are diall

226. Checking the Charge CounterYou can check the battery charged level on the display. The charged level is displayed in 10 stages.1. Press the [On-H

23ALARM FUNCTION1. Error Alarm FunctionWhen you turn the power ON, the PS carries out self-diagnostics to check for any hardware errors.If an error is

24Subscription Registration1. Subscription RegistrationThe PS can store IDs for use with up to 4 RE.Authentication Code (AC) are required for each sys

252. PS-ID display1. Press the [Power] key while pressing and holdingthe [Intercom] and [#] keys to select CS registra-tion mode.Note: • The mode Nos.

26Other Information1. Care and Maintenance• Pressing any of the keys may produce a loud tone. Avoid holding the telephone close to the earwhile pressi

272. Trouble ShootingShould any problem persist contact your dealer.Other InformationProblemTelephone will notswitch onShort battery lifeCalls cannot

7L1028AZAJ

3. Recall (Send earth recall or timed break signalto PBX) ... 204. Changing f

3IntroductionIMPORTANT NOTICE FOR U.K.1) Please ensure that the apparatus is not connected in parallel to any other equipment that isintended for conn

42. Safety InformationThis equipment is intended for use when supplied with power from the charger throughthe AC Adaptor.Other usage will invalidate a

5Getting StartedThis chapter describes preparations and other items you must be aware of before starting operation.Prepare your PS for use as follows:

6Getting Started(4) Slide the battery cover in the direction of the arrow until you hear it click intoposition.2. Charging the PS(1) Plug the AC adapt

7(3) Place the PS with its battery pack in the charger.The charge lamp on the charger lights. While the PS is placed on.Notes:• The first time you cha

83. Turning the power ON/OFF3.1 Turning the power ONWhen the power is turned ON, the PS can be operated.1. Hold the [Power] key down for at least one