Panasonic WV-CW504 Guia de Instalação

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.The model number is

10Precautions for InstallationInstallation work shall be performed in accordance with the technology standard of the electric installation.The product

11Mounting screws • The screws and bolts must be tightenedwith an appropriate tightening torque according to the material and strength

12Major operating controls and their functionsq Power cord* This illustration shows the camera without the inner dome.w Video output cablee Enclosurer

13 q Power cordw Video output cable e Enclosure r Panning table Rotate this table to adjust the panning angle of the camera. t Tilt ad

14PreparationsWhen installing the camera on a wall or a ceiling, there are two methods as specified below. (+ Next page) • Usingatw

15Using a two-gang junction box • Whenthecameraisinstalledusingthetwo-gangjunctionbox,mountthecameraattachment(accessory) to the embed

16z Install the camera mount bracket on the wall/ceiling.Note: • Onlythesametypeofholes,A or B, shall be used for mounting. BBBAAA51mmø27

17x Previously run the cables from the wall or ceiling through the cable access hole. c Mount the attachment onto the mount bracket. Recommend

18Camera installationz Mount the camera. <To mount the camera on a two-gang junction box> q Connect the power cord and the video output cable.

19<To use the camera mount bracket> q Attach the camera onto the camera attachment while aligning the "OPEN" mark of the camera wit

2CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PER

20 w Engage the attachment mounting screw of the camera with the camera mounting hole of the camera attachment and rotate the camera in the dir

21 t Mount the supplied base cover on the camera mount bracket. Important: • To prevent the cables from being caughtwhen the base cov

22x Remove the enclosure and inner dome from the main body by loos-ening the three fixing screws. Loosen the three fixing screws by using

23Adjust the cameraz Be sure to view the monitor for adjustment when the camera angle is adjusted. Connect the monitor for adjustment (e.g. a sm

24x Adjusts the focus. Focus adjustment shall be performed when camera angle adjustment are performed. Adjust the focus by following the

25v To perform fine adjustment of the back focus after the ABF operation indicator goes off and automatic back focus is adjusted, use the right or l

26b Mount the enclosure and inner dome. Tighten the screws that have been loos-ened in Step 2 in page 22 using the sup-plied driver bit.

27Waterproof treatment for the cable joint sectionsAdequate waterproof treatment is required for the cables when the camera with exposed cables is ins

28Important: • Ifopenwiringisconducted,besuretouseconduitsandrunthecablesinsidethetubestopro-tect the cables from direct sunlight.

29Make a connectionCautions: • ONLY CONNECT WV-CW504 TO 24 V AC OR 12 V DC CLASS 2 POWER SUPPLY. (WV-CW504) • Besuretoconnectth

3Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5)

30 • Shrinkingthecable-entrysealisaonetimeprocedure. Do not shrink the cable-entry seal until it has been ascertained that unit is functi

31Optional Heater Unit WV-CW5H (option)Installing the heater unit enables the camera to operate in a low-temperature environment below –30 °C. The

32About the setup menusPerforming each setting item in the setup menu should be completed in advance to use this unit. Perform the settings for each i

33Setup item DescriptionSPECIALCHROMA GAIN Adjusts the chroma level. AP GAIN Adjusts the aperture level. PEDESTAL Adjusts the pedestal (brightness) le

34Screenshot 2The setup mode changes to "ENABLE", and the setup menu becomes ready to be set. Basic operationThe description below exp

35Screenshot 3The selected setup screen in the setup menu appears on the screen. Note: • If the top screen of the setup menu iscalle

36Screen transition diagram MODEL WV-CW500 SERIESCAMERA ID OFFCAMERA SYSTEMBACK-FOCUS SPECIALLANGUAGE END SETUP DISABLE **CAMERA SETUP

37TroubleshootingBefore asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after

38Specifications• BasicPower source: WV-CW500: 220 to 240 V AC 50 Hz WV-CW504: 24 V AC 50 Hz, 12 V DCPower consumption: WV-CW500: 5.1 W (withou

39 When using smoke dome cover (option): Color Mode: 0.2 lx at F1.4 WIDE 0.006 lx (sensitivity up x32, at F1.4 WIDE)* BW mode: 0.02 lx at

4Limitation of liabilityTHIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDIN

40Standard accessoriesCD-ROM* ... 1 pc.Installation Guide (this book) ...

41Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)This symbol on the products and/or accompanyin

42

43

Panasonic Corporationhttp://panasonic.netImporter's name and address to follow EU rules:Panasonic Testing CentrePanasonic Marketing Europe GmbHWi

5ContentsImportant safety instructions ... 3Limi

6PrefaceThis product is a 1/3-inch type {1/3"} CCD color CCTV camera. Connection of this product to a video monitor allows users to use this prod

7About the user manualsTrademarks and registered trademarksThe operating instructions of the camera consist of 2 sets: this book and Operating

8PrecautionsThe following points as well as the con-tents of "Warning" and "Caution" shall be observed. Refer installation work to

9[Precautions for use]This product has no power switch. Turn the power off when cleaning the product. To keep on using with stable performanceParts o