Panasonic DP-6530 Manual do Utilizador

Digital Imaging SystemsOperating Instructions(For Copy Functions)Model No. DP-6530/8130Before operating this equipment, please read these instructio

1234567891011128PRECAUTIONS1. Installation1The DP-6530/8130 should be installed by a qualified service representative.Note: The packing material shoul

1234567891011125-12USING THE SPECIAL FUNCTIONS3Press the desired Memory Number key.- When the paper size is ‘0mm’, the selected MemoryNumber key is va

1234567891011125-135. WEEKLY TIMERUsing the built-in weekly timer, you can have the machine automatically turned ON and OFF at specifiedtimes. For ins

1234567891011125-14USING THE SPECIAL FUNCTIONSWhen original or paper size is required to be specified and youneed to specify it to ‘OTHER’ size (excep

1234567891011125-152Key in the year (last two digits only), month, date,day of the week, time (24-hour format) and minutes,in this order from the left

1234567891011125-16USING THE SPECIAL FUNCTIONSPress the ENERGY SAVER or START key on the control panel. The machine starts to warmitself up.8. S

1234567891011125-17Turn ON the power switch once again when the machine is in the off-mode. Press the START keyduring the sleep mode. The machine s

1234567891011125-18USING THE SPECIAL FUNCTIONS1Press the PROGRAM key to enter the programmenu, and press the CHANGE LANGUAGES key.- If the desired

1234567891011125-1911. USER SELECTION (Initial settings)1Press the PROGRAM key to enter the programmenu, and press the USER SELECTION key.- If the

1234567891011125-20USING THE SPECIAL FUNCTIONS12. DEPARTMENT CODESYou can administer the copy quantity of each group by setting a department code for

1234567891011125-215Input the master code name, and press the SETkey.- Entering letters Page 5-29(Max. 36 characters)6Key in the desired master cod

12345678910111291Handle and use the machine gently and carefully.• Do not place anything on the paper drawers or the original feeding tray.• Never all

1234567891011125-22USING THE SPECIAL FUNCTIONS12. DEPARTMENT CODES (Cont.)2Key in the master code or the department code (5digits), then press SET k

1234567891011125-232Press the ENABLE key, then SET key.3Press the department number where you want toregister the department code, and press theCH

1234567891011125-24USING THE SPECIAL FUNCTIONS12. DEPARTMENT CODES (Cont.)Changing a Specific Department Code1Press the SET DEPARTMENT CODES key in

1234567891011125-255Input the department name you want to register,and press the SET key.- Entering letters Page 5-29(Max. 36 characters)6Key in t

1234567891011125-26USING THE SPECIAL FUNCTIONS12. DEPARTMENT CODES (Cont.)3Press the department number where you want todelete the department code, an

1234567891011125-273Press the department number you want to clearthe counter, and press the RESET COUNTERSkey.1Press the SET DEPARTMENT CODES key i

1234567891011125-28USING THE SPECIAL FUNCTIONSPrint out Department Code*This function prints out the number of copies output for each department.1Pres

1234567891011125-29The following screen is provided for entering letters.* To enter numbers, use the digital keys on the control panel.The following k

1234567891011125-30USING THE SPECIAL FUNCTIONS13. ENTERING LETTERS (Cont.)1Press the B Space key to delete “Meeting”.2Press the Caps Lock key to e

1234567891011125-315Press the B Space key to delete “M”.6Press the N key to enter “N”, then the SET keyto fix the entered characters.4Press the

12345678910111210Explanatory LabelCLASS 1 LASER PRODUCTAPPAREIL A LASER DE CLASSE 1LASER KLASSE 1PRODUCTO DE LASER DE CLASE 1>PS<Certification L

1234567891011125-32USING THE SPECIAL FUNCTIONS

1234567891011126-16. SELECTING FINISHINGMODES(USING THE OPTIONAL FINISHERS)1. FINISHING MODES AND FINISHERS (OPTIONAL)... 6-22. SORT/GROUP

1234567891011126-2SELECTING FINISHING MODES1. FINISHING MODES AND FINISHERS (OPTIONAL)There are 2 types of optional finishers (2-Bin Finisher/DA-FS810

1234567891011126-3Select other copy modes as required.5Press the START key.2. SORT/GROUP COPYINGTo make multiple copies, you can select the sort m

1234567891011126-4SELECTING FINISHING MODES2Place the original(s). Page 2-93. STAPLE SORTING (OPTIONAL)1Place paper in the drawer(s). Page 2-4- Wh

1234567891011126-55 Press the START key.- If the paper quantity exceeds the maximum number of sheetsthat can be stapled, the finisher automatical

1234567891011126-6SELECTING FINISHING MODES123211129476583101127676123213Place the original(s). Page 2-9- When placing them in the reversing automat

1234567891011126-75Press the MAGAZINE SORT ( or MAGAZINE SORT & SADDLE STITCH or SADDLE STITCH ) key.- If the desired function keys are not

1234567891011126-8SELECTING FINISHING MODES2Place the original(s). Page 2-93Press the key on the basic screen as shown on theright (shaded).4Press t

1234567891011127-17. WHEN THE GRAPHIC SYMBOLSFLASH ON THE TOUCH PANEL1. DESCRIPTION OF THE FLASHING GRAPHIC SYMBOLS ... 7-22. ADD PAPER SYMBOL ...

12345678910111211 Fixing the adjusters (stoppers)There are four adjusters (stoppers) located in front and rear bottom(two adjusters each) of the mac

1234567891011127-2WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL1. DESCRIPTION OF THE FLASHING GRAPHIC SYMBOLSThe graphic display on the touch pane

1234567891011127-3Side guideApprox. 0.5mm Approx. 0.5mmSide guideSlide Rail Adding Paper to the Drawers1Pull the drawer out carefully until it comes t

1234567891011127-4WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANELMAXSlide Rail AB1Pull the tandem LCF out carefully until it comes toa stop.- Be car

1234567891011127-5MAXSlide Rail Adding Paper to the External LCF (Large Capacity Feeder) (optional)1Pull the external LCF out carefully until it comes

1234567891011127-6WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANELHere at Panasonic dependable high quality image output is what we do. By using genu

1234567891011127-7Label (orange)Shutter (orange)Holder2Rotate the left end of the holder, then pull out theempty toner bottle with both hands as shown

1234567891011127-8WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANELType of OriginalsA.B.C.A20,00030,00040,00050,00060,00070,00074,000A20,00030,00040,0

1234567891011127-9Reversing Automatic Document FeederInside of the MachineBypass GuideExternal LCF (Optional)Hole Punch Unit (Optional)Finisher (Optio

1234567891011127-10WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL Paper Misfeed in the Reversing Automatic Document Feeder2Rotate the blue knob to

1234567891011127-117Lifting the handle in the direction of the arrow, pullit toward you.6Open the original exit tray and remove any misfedoriginals.8R

1234567891011127-12WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL Paper Misfeed inside of the Machine1Open the paper feed cover.- When installing t

1234567891011127-136Remove any misfed paper.- If any paper is misfed in the cover, pull it out.CautionDo not touch the metal area of guide plate in th

1234567891011127-14WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANELMetal areaFuser unit- If a sheet of paper is misfed on the transfer belt, remove i

1234567891011127-151Pull up the misfed paper slowly on the bypass guide. Paper Misfeed on the Bypass Guide Paper Misfeed in the External LCF (Large Ca

1234567891011127-16WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL4Open the cover of the external LCF and remove anymisfed paper.- Be careful not to

1234567891011127-17Knob212Lift knob (See the upper right figure), thenremove any misfed paper.- For the paper misfed in the position shown on the ri

1234567891011127-18WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL4. CLEAR PAPER SYMBOL (Cont.)4Remove any misfed paper from the paper exit area

1234567891011127-19124Turn the right-hand knob counter clockwise. Then,push the left-hand knob and turn it clockwise.5Remove any paper misfed on t

1234567891011127-20WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL5. ADDING STAPLES (OPTIONAL)When the staple cartridge runs out of staples, if the

1234567891011127-215. ADDING STAPLES (OPTIONAL) (Cont.)6Return the staple cartridge to its original position.- Insert the cartridge until it is caught

1234567891011121-11. BEFORE MAKING COPIES1. DESCRIPTION OF THE DIGITAL IMAGING SYSTEMAND THE OPTIONAL EQUIPMENT... 1-2- Main Components ...

1234567891011127-22WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL3Pull out the grip of the saddle staple holder toward you and turn it 90o clockw

1234567891011127-237Close the lower cover of the finisher. Test staplingis then automatically performed on a blank sheet.- This operation is carried o

1234567891011127-24WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANELWhen copies have not been stapled in the staple mode, the following message may be

1234567891011127-255Return the staple case to its original position.- Insert the cartridge until it is caught by the claw and fixedwith a click sound.

1234567891011127-26WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL5Return the staple case to its original position.6. REMOVING JAMMED STAPLES (OPTIO

1234567891011127-277. DISPOSING OF ACCUMULATED PUNCHED PAPER BITS (OPTIONAL)When paper bits punched from copies have accumulated to a certain level, t

1234567891011127-28WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANELWhen the CALL SERVICE or CLEAR PAPER symbol is flashing, if you press th

1234567891011128-18. MAINTENANCE1. DAILY INSPECTION ... 8-22. SIMPLE TROUBLESHOOTING ...

1234567891011128-2MAINTENANCEScanningarea1. DAILY INSPECTIONItems for Daily CheckPower switch ON/OFF statusWe recommend turning the power switch ON at

1234567891011128-3Press the START or ENERGY SAVERkey on the control panel to clear the automaticenergy saving mode. (It takes a while for themach

1234567891011121-2BEFORE MAKING COPIES1. DESCRIPTION OF THE DIGITAL IMAGING SYSTEM AND THE OPTIONAL EQUIPMENTMain ComponentsOriginal ScalesControl Pan

1234567891011128-4MAINTENANCEIs the reversing automaticdocument feeder firmlyclosed?Is the original cover or thetransport belt of the reversingautomat

1234567891011129-19. SPECIFICATIONS & OPTIONS1. DP-6530/8130 SPECIFICATIONS ... 9-22. SPECIFICATIONS OF OP

1234567891011129-2SPECIFICATIONS & OPTIONS1. DP-6530/8130 SPECIFICATIONSModel NameTypeOriginal GlassCopying SystemDeveloping SystemFixing methodPh

1234567891011129-3FeederDrawer/Tandem LCFBypassDrawerBypassDrawerBypassDrawerBypass *2Drawer/Tandem LCFBypassDrawerBypassDrawerBypassDrawerBypass *2Dr

1234567891011129-4SPECIFICATIONS & OPTIONS2x9.8(2000)5.5(1000)Mixed paper not loaded1, 2xWhichever of 4.3”, 750 sheetsor 100 copies is reached fir

1234567891011129-5Model NameDA-SP81Hole Punch UnitAvailable paper sizes2 holes: LG (Legal), LT-R (Letter-R)3 holes: LD (Ledger), LT (Letter)Paper Weig

1234567891011129-6SPECIFICATIONS & OPTIONS3. PACKING LISTPacking ListSet-up InstructionsSet-up ReportPhotoconductive DrumPhotoconductive Drum Cove

1234567891011129-74. INDEXNumbers2 IN 1 ... 4-122 IN 1 DUPLEX ...

1234567891011129-8SPECIFICATIONS & OPTIONS4. INDEX (Cont.)Duplex Copying ... 3-7EEdge Erase ...

1234567891011129-9Power Switch ... 1-2Precautions ...

1234567891011121-3Optional EquipmentFinisher2-Bin Finisher (DA-FS810)2-Bin Saddle-Stitch Finisher (DA-FS815)Enables the use of sort, group and staple

memo

USA OnlyWARRANTYPANASONIC DIGITAL DOCUMENT COMPANY MAKES NO WARRANTIES, GUARANTEES ORREPRESENTATIONS, EXPRESSED OR IMPLIED, TO CUSTOMER WITH RESPECT T

1234567891011121-4BEFORE MAKING COPIES1. DESCRIPTION OF THE DIGITAL IMAGING SYSTEM AND THE OPTIONAL EQUIPMENT (Cont.)Control PanelTotal CounterShows t

1234567891011121-5 FUNCTION CLEAR keyWhen this key is pressed, all selected copy modes are cleared to default settings. Page 2-2* Automatic Functio

1WARNING: Changes or modification made to this equipment, not expressly approved byPanasonic or parties authorized by Panasonic, could void the user&a

1234567891011121-6BEFORE MAKING COPIES1. DESCRIPTION OF THE DIGITAL IMAGING SYSTEM AND THE OPTIONAL EQUIPMENT (Cont.)Touch PanelThe following informat

1234567891011121-7Clearing the Functions SelectedThe icons displayed on the screen are as follows (some icons may not appear on the screen):If you pre

1234567891011121-8BEFORE MAKING COPIESWhile the above message is displayed, stopping printing due topaper jam, etc. Cancels the job of auto start. To

1234567891011121-9Controlling the Use of the Machine with Department Codes1When the department code function is in use, thescreen shown on the right a

1234567891011122-12. HOW TO MAKE COPIES1. GENERAL COPYING PROCEDURES ... 2-22. SETTING COPY PAPER...

1234567891011122-2HOW TO MAKE COPIESInitial (default) settings1. GENERAL COPYING PROCEDURESAfter placing, or confirming that there is, paper in the dr

1234567891011122-3 - After starting copying, press the JOB STATUS key on the control panel, then press the STATUS key on the touch panel to indica

1234567891011122-4HOW TO MAKE COPIESFeederDrawersTandem LCFExternal LCF(optional)Sheet BypassPaper TypePlain Paper(17- 20 lb Bond)Thick 1( - 90 lb Ind

1234567891011122-5Pay attention to the following points:- Avoid using paper that is specially treated or paper that was printed on another machine, an

11EPA ENERGY STAR ® (MFD)The United States Environmental Protection Agency (EPA) has introduced a voluntary program, the ENERGYSTAR Program, to encour

1234567891011122-6HOW TO MAKE COPIESSlide rail2. SETTING COPY PAPER (Cont.)Changing the Paper Size of the Drawer/Setting the Drawer for Special UsesTh

1234567891011122-78Press the JOB STATUS key on the control panel,then the CASSETTE key on the touch panel.9Press the drawer key corresponding to t

1234567891011122-8HOW TO MAKE COPIES2. SETTING COPY PAPER (Cont.)Changing the Paper Size of the Drawer/Setting the Drawer for Special Uses (Cont.)3Pre

1234567891011122-9Setting placeGlass*1Reversing automaticdocument feeder*2Types of originalsSheetsThree-dimensional objectsBooksPlain paper, recycled

1234567891011122-10HOW TO MAKE COPIES3. SETTING ORIGINALS (Cont.)1Raising the reversing automatic document feeder,place the original in the direction

1234567891011122-11When Using the Reversing Automatic Document FeederOriginals in progress automatically exit on or dependingupon the size of orig

1234567891011122-12HOW TO MAKE COPIESWhen the number of originals is too large to be set at onetime, you can divide the originals into two to ten sets

1234567891011122-134. AUTO JOB START (JOB PRESET)While multi-copying is in process, you can reserve the next copy.1Place the original(s). Page 2-92Pr

1234567891011122-14HOW TO MAKE COPIES5. INTERRUPT COPYING4After you have finished interrupt copying, press theINTERRUPT key again.- The following mes

1234567891011122-151Press the STOP key on the operational panelduring the multicopying operation.If you want to stop the operation during scanning

1234567891011122PREFACEThank you for purchasing the digital imaging system DP-6530/8130.This Operating Instructions describes the following:• how to u

1234567891011122-16HOW TO MAKE COPIESIf data is waiting to be printed, you can delete them, or change the printing order.7. DELETING OR CHANGING ORDER

1234567891011122-17Changing the Printing Order1Press the JOB STATUS key on the control panel,then the JOB LIST key on the touch panel.2Select the

1234567891011122-18HOW TO MAKE COPIES

1234567891011123-13. SETTING OF BASIC COPYMODES1. PAPER SELECTION ... 3-2- Automatic Pape

1234567891011123-2SETTING OF BASIC COPY MODES4Press the START key.1. PAPER SELECTIONAutomatic Paper Selection (APS)- If the Automatic Paper Selecti

1234567891011123-33On the basic screen, press the drawer iconrepresenting the desired paper size.1Place paper in the drawer(s). Page 2-4- When using

1234567891011123-4SETTING OF BASIC COPY MODES2. REDUCTION AND ENLARGEMENT COPYINGWhen placing originals on the glass, you can copy them at the reducin

1234567891011123-54Press the key corresponding to the original size.- Using the original size and copy size, the correctreproduction ratio is computed

1234567891011123-6SETTING OF BASIC COPY MODES2. REDUCTION AND ENLARGEMENT COPYING (Cont.)3Press the drawer icon representing the desired copypaper siz

1234567891011123-7-12--13--15- -12- -13- -15--13--13-3. DUPLEX COPYING (1-SIDED, 2-SIDED, BOOK-TYPE)This function allows you to set the type of origin

1234567891011123PREFACE (Cont.)Features of the DP-6530/8130The DP-6530/8130 is a digital imaging system which is high-speed, compact and high-durabili

1234567891011123-8SETTING OF BASIC COPY MODES3. DUPLEX COPYING (1-SIDED, 2-SIDED, BOOK-TYPE) (Cont.)3Press the key (shaded) on the right basic screen.

1234567891011123-93Select the book copying type.- Press the RIGHT RIGHT key if copying should start at aright-hand page and end at a right-hand pag

1234567891011123-10SETTING OF BASIC COPY MODES7Turn to the next page, set the book again and pressthe START key.- Repeat the procedure above until

1234567891011123-11- If the automatic density mode is not selected, press theMANUAL key, then press the AUTO key on the nextscreen.4. COPY DENSITY

1234567891011123-12SETTING OF BASIC COPY MODES4. COPY DENSITY ADJUSTMENT (Cont.)- When the DENSITY LEVEL key is shown on the lower left ofthe screen,

1234567891011123-135. SELECTING ORIGINAL MODEAccording to the type of your originals, you can choose among the three image types: Photo, Text or Text/

1234567891011123-14SETTING OF BASIC COPY MODES6. QUICK ACCESS MENUFinishing copy and duplex modes can be performed at the same time on one display by

1234567891011124-14. USING THE EDITINGFUNCTIONS1. IMAGE SHIFT ... 4-22. EDGE ER

1234567891011124-2USING THE EDITING FUNCTIONS1. IMAGE SHIFT1Place paper in the drawer(s). Page 2-4- When using this mode in bypass copying, be sure

1234567891011124-31Press the EDIT key to enter the edit menu, andpress the IMAGE SHIFT key.3Adjust the width of the margin, then press the SETkey.

1234567891011124Energy Star ...

1234567891011124-4USING THE EDITING FUNCTIONS3Press the EDIT key to enter the edit menu, andpress the EDGE ERASE key. Select other copy modes as r

1234567891011124-52Press the EDIT key to enter the edit menu, andpress the DUAL PAGE key.5If you need a binding margin, set the left margin. Page

1234567891011124-6USING THE EDITING FUNCTIONS7Turn to the next page, set the book again andpress the START key.- Repeat the above procedure until a

1234567891011124-75Press the lower SET key.4Set the reproduction ratios for the X (horizontal)and Y (vertical) directions, respectively.- Using th

1234567891011124-8USING THE EDITING FUNCTIONS3Press the TRIM (or MASK ) key.2Press the EDIT key to enter the edit menu, andpress the EDITING ke

1234567891011124-96Enter the distance values read in step 5 for thespecified area.- Key in the value for X1 with the digital keys and press theupper

1234567891011124-10USING THE EDITING FUNCTIONS Select other copy modes as required.5Press the START key.3Press the EDIT key to enter the edit men

1234567891011124-11 Select other copy modes as required.5Press the START key.2Place the original(s). Page 2-93Press the EDIT key to enter the e

1234567891011124-12USING THE EDITING FUNCTIONSWhen a copy is turned with the line —·—·— as a pivot, originals are printed on side 2 (back face) asshow

1234567891011124-13 Select other copy modes as required.6Press the START key.- When placing an original on the glass, perform steps 5 and6 on page

12345678910111254.USING THE EDITING FUNCTIONS ... 4-11. IM

1234567891011124-14USING THE EDITING FUNCTIONSCopies are made with the current date and time, at which they are made, printed on the copy.Date and tim

1234567891011124-15This feature allows numbers to be added at specified position to copies.Page number printed at the bottomcenter on the portrait cop

1234567891011124-16USING THE EDITING FUNCTIONSThe magazine sort mode allows 1-sided originals to be copied and sorted so that they can be folded andbo

1234567891011124-17- If the optional saddle stitch finisher (MJ-1018, MJ-1021) isinstalled, copies can be automatically stapled along theircenter line

1234567891011124-18USING THE EDITING FUNCTIONSA top cover and/or back cover (special sheets, e.g. colored paper) can be added to each set of copies.-

1234567891011124-195Select the desired cover sheet key:To add a blank top cover: TOP BLANKTo add a copied top cover: TOP COPIEDTo add blank top and ba

1234567891011124-20USING THE EDITING FUNCTIONSTab paper back guideSlide rail11. TAB PAPER MODETab paper copy and insertion are available.Copy on Tab:

1234567891011124-21To copy on tab paper, adjust both the tab width and the shift width for the drawer and the bypass guiderespectively. Tab Width Adju

1234567891011124-22USING THE EDITING FUNCTIONSTab widthAlign the tab paper withthe original scaleOriginal scaleShift widthAlign the original withthe o

1234567891011124-231Place tab paper in the drawer or the bypass guide.- For placing it in the drawer Page 4-22- For placing it in the bypass guide

12345678910111267.WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL ... 7-11. DESCRIPTION OF THE FLASHING GRAP

1234567891011124-24USING THE EDITING FUNCTIONS5Key in the page number you selected for theinsertion of the tab paper , then press the upperSET key.-

1234567891011124-255Key in the page number you selected for theinsertion of the tab paper, then press the upperSET key.- When two sheets of paper or

1234567891011124-26USING THE EDITING FUNCTIONS1Place the original(s). Page 2-92Press the EDIT key to enter the edit menu, andpress the DOCUMENT S

1234567891011124-275Press the START key.- The memorization process starts automatically.- To change the file name, select the ID you want to chang

1234567891011124-28USING THE EDITING FUNCTIONS13. OVERLAYThis function stores the images that you frequently use and makes copies by overlaying onto t

1234567891011124-29Confirming Stored Image (Test Print)1Perform steps 2 and 3. Page 4-292Press the file name you desire (the selected filename will

1234567891011124-30USING THE EDITING FUNCTIONS13. OVERLAY (Cont.)Overlaying Originals with Stored Image4Press the OVERLAY key.5Press the file name y

1234567891011124-3114. SHARPNESS ADJUSTMENT5Press the SET key. Select other copy modes as required.2Place the original(s). Page 2-93Press the EDI

1234567891011124-32USING THE EDITING FUNCTIONS15. DIRECTION OF DUPLEX COPY IMAGES (Rotation)When lengthLD (Ledger) paper is copied under the mode of 1

1234567891011125-15. USING SPECIALFUNCTIONS1. CONTINUOUS ORIGINAL FEEDING /SINGLE ORIGINAL FEEDING ... 5-22. MIXED-SIZED ORIGINALS ...

1234567891011127The following notice sets out the exclusions and limitations of liability of Panasonic (including its employees,agents and sub-contrac

1234567891011125-2USING THE SPECIAL FUNCTIONS Select other copy modes as required.5Press the START key.When the number of originals is too large t

1234567891011125-3Single-feed Mode3Press the SADF key. Select other copy modes as required.4Place an original. Page 2-9- The original is automatic

1234567891011125-4USING THE SPECIAL FUNCTIONS3Press the PROGRAM key to enter the programmenu, and press the MIXED ORIGINAL SIZESkey.2. MIXED-SIZED

1234567891011125-52Press the PROGRAM key to enter the programmenu, and press the JOB MEMORY key.3. JOB MEMORYStoring a Combination of Copy Job Set

1234567891011125-6USING THE SPECIAL FUNCTIONS4Press the RECALL key.3. JOB MEMORY (Cont.)2Place the original(s). Page 2-95Press the Memory Number k

1234567891011125-7To confirm the copy modes stored in the Memory Number key,perform steps 3 to 5 on the previous page, then press theSETTINGS key.Con

1234567891011125-8USING THE SPECIAL FUNCTIONSMAX4. BYPASS COPYINGWhen you want to make copies on thick paper, OHP film, tab paper, tracing paper, stic

1234567891011125-94After selecting the paper type corresponding to thetype of the paper that has been set, press the SETkey.- When selecting OHP film,

1234567891011125-10USING THE SPECIAL FUNCTIONS4. BYPASS COPYING (cont.)Bypass Copying on Standard Size Paper1perform steps 1 to 2 on pages 5-8, 5-9.-S

1234567891011125-112Press the NON-STANDARD key.1Perform steps 1 to 3 on page 5-10.The size of non-standard paper is within the following ranges: Le